VehiclesKyosho Fazer Mk2 FZ02-R
Kyosho Fazer Mk2 FZ02-R Chassis
1/10 scale · 4WD rally chassis · sold as kits
Kyosho's Fazer Mk2 FZ02-R is the rally version of the FZ02, a 1/10 four-wheel-drive, shaft-driven chassis on a 260 mm wheelbase with longer-travel oil shocks and more ground clearance.
It keeps the 68T spur and the 3.08:1 gearbox and axle stage, and Kyosho fits a sintered pinion that copes with gravel and dirt. The motor and tires come with each readyset rather than with the chassis, so enter the pinion you run in the gearing tool and check the motor temperature after a rough run.
- Transmission & axle
- 3.08:1
- Spur
- 68T
- Wheelbase
- 260mm
- Introduced
- 2023
The pinion, motor and tires come with each kit: enter yours in the gearing tool.

Kits on this chassis Built on the Fazer Mk2 FZ02-R
Each kit adds its own body, tires, pinion and motor. The chassis figures below apply to all of them.
| Kit | Part no. | Maker page |
|---|---|---|
| 34481T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34482T1 | rc.kyosho.comPage (opens in a new tab) |
Specifications
Last modified
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Rally | |
| Drive | 4WD | |
| Scale | 1/10 | |
| Drivetrain | ||
| ||
| Pinion | With each kit | |
| Spur | 68TStock | Stock |
| Transmission & axle | 3.08:1Derived | Derived |
| Final drive | With each kit | |
| Wheels & tires | ||
| ||
| Tire diameter | With each kit | |
| Power | ||
| ||
| Motor | With each kit | |
| Battery | With each kit | |
| Size & weight | ||
| ||
| Wheelbase | 260 mm10.2 inStock | Stock |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Derived is worked out from gear tooth counts the maker publishes rather than printed as a ratio; the notes below say how.
- With each kit means each kit on this chassis brings its own, so enter yours in the gearing tool.
Other versions of this chassis
Gearing parts
| Component | Teeth | Pitch | Bore | Part number |
|---|---|---|---|---|
| Fitted at the factory | ||||
| Spur | 68T | Not published | Not applicable | FA556-68 (opens in a new tab) |
About teeth, pitch and bore
- Tooth counts are the ones in the specifications above.
- Pitch is given as metric module (Mod 1, Mod 0.8) or diametral pitch (32P, 48P). They are different standards and are not interchangeable, even where the numbers look close.
- Bore is the pinion’s hole, listed separately from the motor shaft.
- Linked part numbers go to the maker’s or official distributor’s page for that part.
How these numbers were settled
The rally version of the FZ02: Kyosho gives it 'front and rear shock stays developed to support oil shocks with pistons and cases designed for rally use', which 'allows higher ground clearance and longer suspension stroke', and rally steering parts.
- The gearing is the FZ02's: the FZ02-R kit pages print 'Gear Ratio 6.54:1' and a 'sintered 32T pinion gear', with motor mounts for pinions 'ranging from 29T to 37T', and the FZ02-R spare parts list names the FA556-68 'TC Spur Gear 68T FZ02'.
- The ratio after the spur works out at 6.54 x 32 / 68 = 3.078.
- The kit pages print a 260mm wheelbase.
- The pinion, motor and tires come with each kit (tire widths differ between the readysets), so enter yours in the gearing tool.
Sources
Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.
Maker documents
- Instruction manual, FZ02-R (Kyosho PDF) (opens in a new tab)kyosho.com
- Spare parts list, FZ02-R (Kyosho PDF) (opens in a new tab)FA556-68kyosho.comUsed forMain specsGearing
Parts and electronics
- 34481T1 (opens in a new tab)rc.kyosho.comUsed forMain specsSize
- 34482T1 (opens in a new tab)rc.kyosho.comUsed forMain specsSize
- FZ02 R (opens in a new tab)rc.kyosho.comUsed forMain specs
- Kyosho FA556-68 spur gear (opens in a new tab)rc.kyosho.comUsed forMain specsGearing
