VehiclesKyosho Fazer Mk2 FZ02
Kyosho Fazer Mk2 FZ02 Chassis
1/10 scale · 4WD touring chassis · sold as kits
Kyosho's Fazer Mk2 FZ02 is a 1/10 four-wheel-drive, shaft-driven touring chassis on a 260 mm wheelbase, sold as readysets under many scale bodies.
Every kit on it shares the 68T spur and a 3.08:1 gearbox and axle stage, so the final drive depends only on the pinion fitted to the motor. Kyosho's motor mount has a hole for each pinion size, so a change needs no mesh setting. The motor, pinion and tires come with each kit rather than with the chassis, so enter yours in the gearing tool.
- Transmission & axle
- 3.08:1
- Spur
- 68T
- Wheelbase
- 260mm
- Introduced
- 2019
The pinion, motor and tires come with each kit: enter yours in the gearing tool.

Kits on this chassis Built on the Fazer Mk2 FZ02
Each kit adds its own body, tires, pinion and motor. The chassis figures below apply to all of them.
| Kit | Part no. | Maker page |
|---|---|---|
| 34471T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34493T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34418T1C | rc.kyosho.comPage (opens in a new tab) | |
| 34429T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34424C | rc.kyosho.comPage (opens in a new tab) | |
| 34428T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34445T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34427T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34426T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34425T1C | rc.kyosho.comPage (opens in a new tab) | |
| 34424T2 | rc.kyosho.comPage (opens in a new tab) | |
| 34423 | rc.kyosho.comPage (opens in a new tab) |
Show 6 more kits
| Kit | Part no. | Maker page |
|---|---|---|
| 34422T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34472T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34473T1 | rc.kyosho.comPage (opens in a new tab) | |
| 34441 | rc.kyosho.comPage (opens in a new tab) | |
| 34421 | rc.kyosho.comPage (opens in a new tab) | |
| 34418T2 | rc.kyosho.comPage (opens in a new tab) |
Specifications
Last modified
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Touring | |
| Drive | 4WD | |
| Scale | 1/10 | |
| Drivetrain | ||
| ||
| Pinion | With each kit | |
| Spur | 68TStock | Stock |
| Transmission & axle | 3.08:1Derived | Derived |
| Final drive | 5.66 to 7.22:1 on 37T to 29T pinionsMaker's chart | Maker's chart |
| Wheels & tires | ||
| ||
| Tire diameter | With each kit | |
| Power | ||
| ||
| Motor | With each kit | |
| Battery | With each kit | |
| Size & weight | ||
| ||
| Wheelbase | 260 mm10.2 inStock | Stock |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Derived is worked out from gear tooth counts the maker publishes rather than printed as a ratio; the notes below say how.
- With each kit means each kit on this chassis brings its own, so enter yours in the gearing tool.
- Maker’s chart is the ratios the maker prints for this chassis with the pinions it names.
Other versions of this chassis
Gearing parts
| Component | Teeth | Pitch | Bore | Part number |
|---|---|---|---|---|
| Fitted at the factory | ||||
| Spur | 68T | Not published | Not applicable | FA556-68 (opens in a new tab) |
About teeth, pitch and bore
- Tooth counts are the ones in the specifications above.
- Pitch is given as metric module (Mod 1, Mod 0.8) or diametral pitch (32P, 48P). They are different standards and are not interchangeable, even where the numbers look close.
- Bore is the pinion’s hole, listed separately from the motor shaft.
- Linked part numbers go to the maker’s or official distributor’s page for that part.
How these numbers were settled
Every FZ02 readyset shares the 68T spur and the gearbox and axle stage after it.
- Kyosho prints the complete motor-to-wheel ratio on each kit, 'Gear Ratio 6.54:1', and says the 'Standard spur and pinion gear setting is 68T and 32T', with nine pinions from 29T to 37T usable; the ratio after the spur works out at 6.54 x 32 / 68 = 3.078.
- Older bodies such as the Alpine GT4 and Audi R8 LMS 2015 readysets print the total rounded to 6.5:1 with the same 68T and 32T gears.
- The FZ02-D drift readysets use the same gears and 260mm wheelbase with drift tires, and the FZ02 VE readyset fits a brushless motor on the same 6.54:1 gearing.
- The spur is Kyosho's FA556-68 'TC Spur Gear 68T FZ02'.
- The pinion, motor and tires come with each kit, so they are not part of the chassis figures: enter yours in the gearing tool.
- Every FZ02 kit page prints a 260mm wheelbase; the long-wheelbase FZ02L, the rally FZ02-R and the FZ02 Chassis Kit (34461C) have sheets of their own.
- The manual lists 29T to 37T pinions for the stock spur; the ratios 7.22:1 to 5.66:1 are worked out from them with the figures above.
Sources
Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.
Maker documents
- Instruction manual, FZ02/FZ02L (Kyosho PDF) (opens in a new tab)kyosho.comUsed forMain specs
Parts and electronics
- 34429T1 (opens in a new tab)rc.kyosho.comUsed forMain specsSize
- 34424C (opens in a new tab)rc.kyosho.comUsed forMain specsSize
- 34445T1 (opens in a new tab)rc.kyosho.comUsed forMain specs
- 34426T1 (opens in a new tab)rc.kyosho.comUsed forMain specs
- EN 34423 (opens in a new tab)rc.kyosho.comUsed forMain specs
- Fazer FZ02 (opens in a new tab)rc.kyosho.comUsed forMain specs
- Kyosho FA556-68 spur gear (opens in a new tab)rc.kyosho.comUsed forMain specsGearing
- FZ02 FZ02L T04 IM (PDF) (opens in a new tab)kyosho.comUsed forMain specs
