VehiclesSchumacher CAT 2000 Classic
Schumacher CAT 2000 Classic Chassis
1/10 scale · 4WD buggy chassis kit · K221
Schumacher's CAT 2000 Classic is a four-wheel-drive 1/10 buggy kit, a belt-driven re-release built by you and sold without motor or electronics.
It comes with a 95T spur on a single plate slipper, and the transmission reduces 2.00:1 after it, so the pinion you fit sets the overall ratio. The buggy is 400 mm long with a 285 mm wheelbase. Pick the pinion for the motor you run, and check that the slipper is set loose enough to protect the 95T spur on landings.
- Transmission & axle
- 2.00:1
- Spur
- 95T
- Wheelbase
- 285mm
- Introduced
- 2025
Sold without a motor, so there is no stock KV: compare gearing by rollout.

Specifications
Last modified
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Buggy | |
| Drive | 4WD | |
| Power | Motor not included | |
| Build | Kit | |
| Scale | 1/10 | |
| Part number | K221 | |
| Drivetrain | ||
| ||
| Pinion | Not applicable | |
| Spur | 95TStock | Stock |
| Transmission & axle | 2.00:1Stock | Stock |
| Final drive | Not applicable | |
| Wheels & tires | ||
| ||
| Tire diameter | Not published | |
| Power | ||
| ||
| Motor | Not applicable | |
| Motor shaft | Not applicable | |
| Battery | Not applicable | |
| Performance | ||
| ||
| Theoretical top speed | Not applicable | |
| Size & weight | ||
| ||
| Length | 400 mm15.7 inStock | Stock |
| Width | 245 mm9.6 inStock | Stock |
| Wheelbase | 285 mm11.2 inStock | Stock |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Not applicable means the vehicle does not come with it, like the motor on a roller or the tires on a race kit, or does not have one, like a KV rating on a brushed motor.
- Not published means it exists but no source we could find prints it.
Gearing parts
| Component | Teeth | Pitch | Bore | Part number |
|---|---|---|---|---|
| Fitted at the factory | ||||
| Spur | 95T | Not recorded | Not applicable | U8984 |
About teeth, pitch and bore
- Tooth counts are the ones in the specifications above.
- Pitch is given as metric module (Mod 1, Mod 0.8) or diametral pitch (32P, 48P). They are different standards and are not interchangeable, even where the numbers look close.
- Bore is the pinion’s hole, listed separately from the motor shaft.
How these numbers were settled
Re-release of Schumacher's belt-driven 4WD buggy, with two ball diffs and a single plate slipper.
- The manual prints the gear ratio as 2.00:1 above a chart whose spur column marks the 95T as the kit build ('95KB'), and its transmission spares list the 95T slipper spur (U8984); the chart reconciles with spur over pinion times 2.00 (95/19 gives 10).
- The kit includes Schumacher tyres, wheels and inserts, but no tyre size is published, so it is left blank.
- Motor, long boss pinion, speed controller and servo are on the list of items to buy.
Sources
Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.
Maker documents
- Instruction manual, CAT 2000 Classic (Schumacher PDF) (opens in a new tab)Gear ratio p. 27; spares list p. 29racing-cars.comUsed forMain specsGearing
- Exploded diagram (Schumacher PDF) (opens in a new tab)racing-cars.com
This vehicle
- Schumacher CAT 2000 Classic product page (opens in a new tab)racing-cars.comUsed forMain specsSize
Parts and electronics
- Schumacher cat 2000 classic (opens in a new tab)redrc.netUsed forMain specs
