VehiclesWLtoys 184011

- Scale
- 1/18
- Drive
- -
- Max LiPo
- -
- Power
- brushed
Background
The WLtoys 184011 is a ready-to-run four-wheel-drive buggy built around a 390 brushed motor. Independent suspension and proportional controls give it the basic layout expected of a small hobby-style off-road car. Model information (opens in a new tab).
Read moreShow less
Compared with WLtoys' brushless cars, its brushed power system gives it a different starting point for motor and speed-controller replacements. The listed 30 km/h claim places it below the faster brushless models in the range. Battery and dimension descriptions vary between sellers, so the supplied pack label and exact model marking are useful checks before buying replacements. Model information (opens in a new tab).
Specifications
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Buggy | |
| Power | Brushed | |
| Build | Ready to run | |
| Scale | 1/18 | |
| Part number | 184011 | |
| Drivetrain | ||
| ||
| Pinion | Not published | |
| Spur | Not published | |
| Transmission & axle | Not published | |
| Final drive | Not published | |
| Wheels & tires | ||
| ||
| Tire diameter | Not published | |
| Power | ||
| ||
| Motor | Not published | |
| Battery | Not published | |
| Stock motor | 390 brushed motorStock | Stock |
| Performance | ||
| ||
| Theoretical top speed | Not published | |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Not published means it exists but no source we could find prints it.
Build and setup
Factory setup guide for this configuration.
Plan a radio change around the 184011's original electronics. This handbook describes a combined receiver/control arrangement and a five-wire steering servo. A conventional receiver therefore needs a compatible servo and controller as part of the conversion, with the actual plugs and wiring checked before buying components.[1] 184011 factory setup manual (opens in a new tab)
For routine chassis work, use the separate differential and steering drawings to keep small hardware organized. Retain each differential's bearings, internal pins and shims with that assembly. Restore the servo-saver and linkage arrangement before setting trim, then check steering movement on the bench.[1] 184011 factory setup manual (opens in a new tab)
OEM parts
Drivetrain
5Differential case
Drive gear
Ball bearing, 7 x 11 x 3
Ball bearing, 8 x 12 x 3.5
Suspension
4Shock absorber plate
Suspension arm
Suspension pin, 2 x 40.8
Suspension arm reinforcement plate
Steering
2Servo rod
Servo arm
Electronics
3Motor mounting base
Motor heatsink
Motor gear
Chassis & body
1Rear wing
Hardware & seals
4Pan-head machine screw, 2.5 x 10
Pan-head machine screw, 2.5 x 8
Round-head self-tapping screw, 2 x 16
Ball-head screw, 4 x 10.8
Unclassified
1R-type pin
20 collected part numbers. Collected . Unmarked parts are recorded listings, without a claim about factory installation; optional and upgrade listings are tagged. Key assemblies include recorded gear and shock identifiers. Open a part for its listing sources.
About these specs
Exact configuration is identified by model number. Published battery capacity describes the supplied pack; no unsupported maximum cell rating is inferred.
Sources
4 source links for this model.
Read moreShow less
- Manuals.
- Vehicle product and specification pages.
- Individual part and electronics specifications.
Links open in a new tab.
Maker documents
1- 184011 instruction manual (Hobbyteam factory scan) (opens in a new tab)Supports 1 specificationUsed forMain specs
This vehicle
2- WLtoys 184011 product page (opens in a new tab)Supports 2 specificationsUsed forMain specsElectronicsBackground
- WLtoys 184011 product page (opens in a new tab)Supports 1 specificationUsed forMain specs
Parts and electronics
1- Products details 104 (opens in a new tab)Supports 1 specificationUsed forMain specs
