VehiclesTamiya TT-01 Type-E
Tamiya TT-01 Type-E Chassis
1/10 scale · 4WD touring chassis · sold as kits
Tamiya's TT-01 Type-E is a 1/10 four-wheel-drive, shaft-driven chassis sold as kits under touring car and race truck bodies.
Every kit on it uses the 61T spur and a 2.60:1 gearbox and axle stage on a 257 mm wheelbase, so the pinion you fit sets the gearing. The pinion, motor and tires come with each kit rather than with the chassis. To compare a kit with another car, enter its pinion and tire size in the gearing tool with the 61T spur.
- Transmission & axle
- 2.60:1
- Spur
- 61T
- Wheelbase
- 257mm
- Introduced
- 2008
The pinion, motor and tires come with each kit: enter yours in the gearing tool.

Kits on this chassis Built on the TT-01 Type-E
Each kit adds its own body, tires, pinion and motor. The chassis figures below apply to all of them.
| Kit | Part no. | Maker page |
|---|---|---|
| 58632 | tamiya.comPage (opens in a new tab) | |
| 58683 | tamiya.comPage (opens in a new tab) | |
| 58661 | tamiya.comPage (opens in a new tab) | |
| 58642 | tamiya.comPage (opens in a new tab) | |
| 58638 | tamiya.comPage (opens in a new tab) | |
| 47452 | tamiya.comPage (opens in a new tab) | |
| 47437 | tamiya.comPage (opens in a new tab) | |
| 47430 | tamiya.comPage (opens in a new tab) | |
| 47429 | tamiya.comPage (opens in a new tab) | |
| 47397 | tamiya.comPage (opens in a new tab) | |
| 47372 | tamiya.comPage (opens in a new tab) |
Specifications
Last modified
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Touring | |
| Drive | 4WD | |
| Build | Kit | |
| Scale | 1/10 | |
| Drivetrain | ||
| ||
| Pinion | With each kit | |
| Spur | 61TStock | Stock |
| Transmission & axle | 2.60:1Derived | Derived |
| Final drive | With each kit | |
| Wheels & tires | ||
| ||
| Tire diameter | With each kit | |
| Power | ||
| ||
| Motor | With each kit | |
| Battery | With each kit | |
| Size & weight | ||
| ||
| Wheelbase | 257 mm10.1 inStock | Stock |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Derived is worked out from gear tooth counts the maker publishes rather than printed as a ratio; the notes below say how.
- With each kit means each kit on this chassis brings its own, so enter yours in the gearing tool.
How these numbers were settled
Every TT-01 Type-E kit shares the 61T spur and the gearbox and axle stage after it.
- Tamiya prints only the complete motor-to-wheel ratio on each kit page ('ギヤ比=8.35:1' on the Mercedes-Benz 190 E and the Actros truck), so the stage after the spur is derived.
- Tamiya's Grand Prix rules give the TT-01 a 61T spur with a 19T pinion for the A-Main class and list 61T/21T as 7.55:1, which gives 7.55 x 21/61 = 2.599.
- The same 2.6 on 61T/19T reproduces the kit pages' 8.35:1, (61/19) x 2.6 = 8.347.
- The pinion, motor and tires come with each kit; the 1/14 race trucks use this 1/10 chassis.
- The kit pages print a 257mm wheelbase.
Sources
Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.
Parts and electronics
- Products 58638 (opens in a new tab)tamiya.comUsed forMain specsSize
- Products 58683 (opens in a new tab)tamiya.comUsed forMain specsSize
- REGULATION2024RCCGP (PDF) (opens in a new tab)tamiya.comUsed forMain specs
- Rccgp REGU2026 2 (PDF) (opens in a new tab)tamiya.comUsed forMain specs
- Products 58632 (opens in a new tab)tamiya.comUsed forMain specs
- Products 47372 (opens in a new tab)tamiya.comUsed forMain specs
