VehiclesTamiya TA07 PRO Chassis Kit
Tamiya TA07 PRO Chassis Kit Chassis
1/10 scale · 4WD touring chassis kit · 58636
Tamiya's TA07 PRO Chassis Kit is a 1/10 four-wheel-drive, single-belt touring car kit with a transverse motor, sold without body, motor or tires.
Its gearbox and axle stage after the spur is 2.05:1, so the spur and pinion you fit decide the final drive. It is 370 mm long on a 257 mm wheelbase. For club racing, check the class gearing rules before choosing a pinion.
- Transmission & axle
- 2.05:1
- Spur
- 64T
- Wheelbase
- 257mm
- Introduced
- 2016
Sold without a motor, so there is no stock KV: compare gearing by rollout.

Specifications
Last modified
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Touring | |
| Drive | 4WD | |
| Build | Kit | |
| Scale | 1/10 | |
| Part number | 58636 | |
| Drivetrain | ||
| ||
| Pinion | Not published | |
| Spur | 64TStock | Stock |
| Transmission & axle | 2.05:1Stock | Stock |
| Final drive | 5.06 to 7.74:1 on 26T to 17T pinionsMaker's chart | Maker's chart |
| Wheels & tires | ||
| ||
| Tire diameter | Not applicable | |
| Power | ||
| ||
| Motor | Not applicable | |
| Battery | Not applicable | |
| Performance | ||
| ||
| Theoretical top speed | Not applicable | |
| Size & weight | ||
| ||
| Length | 370 mm14.6 inStock | Stock |
| Width | 187 mm7.4 inStock | Stock |
| Wheelbase | 257 mm10.1 inStock | Stock |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Not applicable means the vehicle does not come with it, like the motor on a roller or the tires on a race kit, or does not have one, like a KV rating on a brushed motor.
- Not published means it exists but no source we could find prints it.
- Maker’s chart is the ratios the maker prints for this chassis with the pinions it names.
Other versions of this chassis
How these numbers were settled
Single-belt 4WD touring chassis kit with a transverse motor that mounts in three positions.
- Tamiya prints no gear ratio for the kit itself; its 2026 All-Japan Championship rules list the TA07(R) on a 105T spur with a 30T pinion at 7.17:1, which gives the ratio after the spur: 7.17 x 30/105 = 2.049.
- The 2024 rules list the TA07 on 64T/18T at 7.31:1, 7.31 x 18/64 = 2.056, so 2.05 is derived from two Tamiya tables that agree within rounding.
- The manual's gear table (PDF p. 23) prints 'Spur gear teeth (64T) / Pinion gear teeth x 2.05', which gives the kit spur and the ratio after it.
- The pinion is not on the list of items to buy, and the page does not give its size, so the pinion and the final drive are left blank.
- Tires, motor and speed controller are sold separately.
Sources
Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.
Maker documents
- TA07 PRO instruction manual (Tamiya PDF) (opens in a new tab)d7z22c0gz59ng.cloudfront.net
This vehicle
- Tamiya TA07 PRO Chassis Kit product page (opens in a new tab)tamiya.comUsed forMain specsSize
- Tamiya TA07 PRO Chassis Kit product page (opens in a new tab)tamiya.comUsed forMain specs
Parts and electronics
- Regulation ALLJAPAN2026 2 (PDF) (opens in a new tab)tamiya.comUsed forMain specs
- REGULATION2024RCCGP (PDF) (opens in a new tab)tamiya.comUsed forMain specs
