VehiclesRedcat Racing 1993 Nissan Hardbody Bed Dancer Founders Edition
Redcat Racing 1993 Nissan Hardbody Bed Dancer Founders Edition
1/10 scale · street · RER43259

- Scale
- 1/10
- Drive
- -
- Max LiPo
- 3S
- Power
- brushed
Background
The Founders Edition Bed Dancer is Redcat Racing's 1/10-scale ready-to-run lowrider pickup with a licensed 1993 Nissan Hardbody D21 body, a 380 brushed drive motor and an LR6X six-channel radio. Founders Edition identity (opens in a new tab).
Read moreShow less
The dedicated chassis reproduces lowrider bed movement through servos and a cable-driven Z rack. It is intended for slow cruising and display routines. The Founders Edition manual shows the supplied radio, decals and extra mag-wheel set, while the battery and charger are separate purchases. Keep this chassis separate from the LRH285 hopping-car kits when ordering bed, body or suspension parts. Factory manual (opens in a new tab).
Specifications
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Street | |
| Power | Brushed | |
| Build | Ready to run | |
| Scale | 1/10 | |
| Part number | RER43259 | |
| Drivetrain | ||
| ||
| Pinion | Not published | |
| Spur | Not published | |
| Transmission & axle | Not published | |
| Final drive | Not published | |
| Wheels & tires | ||
| ||
| Tire diameter | Not published | |
| Wheel hex | 12 mmDerived from replacement part | Derived from replacement part |
| Suspension | ||
| ||
| Chassis | SteelStock | Stock |
| Power | ||
| ||
| Motor | Not published | |
| Motor shaft | Not published | |
| Battery | 2S to 3SLiPoStock | Stock |
| Stock motor | RER13454 RC380 brushed motorStock | Stock |
| Stock ESC | RER15741 R6A 2-in-1 ESC/receiverStock | Stock |
| Motor size | 380canStock | Stock |
| ESC rating | 40 Acontinuous, 200 A burstStock | Stock |
| Battery pack configuration | Separate 2S-3S LiPo; manufacturer-listed footprint 47 x 96 mmTwo listed dimensions only, without axes, height or verified maximum bay clearance. Confirm connector and pack polarity on the actual vehicle.Stock | Stock |
| ESC mounting dimensions | 44.0 x 30.0 x 16.7 mmFactory listed ESC dimensions; not available chassis clearance.Stock | Stock |
| Steering & radio | ||
| ||
| Transmitter | LR6X6-channelStock | Stock |
| Performance | ||
| ||
| Theoretical top speed | Not published | |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Derived from replacement part uses the listed dimensions of a replacement advertised for the identified OEM part. Treat it as an approximate working size; the factory-fitted part may differ. Calculated performance uses that approximation.
- Not published means it exists but no source we could find prints it.
Build and setup
Factory setup guide for this configuration.
Set the Bed Dancer steering mechanically before using radio adjustments to hide an offset. Redcat starts with steering trim and subtrim at zero, then centers the powered servo and installs its horn in the illustrated position. Its next step sets the right steering endpoint from the horn geometry and matches the left endpoint to that value. Recheck endpoints after changing subtrim; the radio chapter says subtrim changes affect the travel limits.[1] 1993 Nissan Hardbody Bed Dancer Founders Edition factory setup and maintenance manual (opens in a new tab)
For bed movement, use the Founders Edition channel map rather than a generic lowrider radio setup. Channels 3 and 4 operate the two forward/back bed stages; channels 5 and 6 operate the side-to-side stages. Redcat warns that the endpoint screen contains example values and that the vehicle may need different values. Keep the supplied mix settings as the baseline, and save intentional radio changes with the Cancel/Save control.[1] 1993 Nissan Hardbody Bed Dancer Founders Edition factory setup and maintenance manual (opens in a new tab)
Read moreRead less about build and setup for 1993 Nissan Hardbody Bed Dancer Founders Edition
Ride height also has a mechanical adjustment independent of the radio. The manual identifies separate front and rear screws. With the body installed, it shows front access through the open hood and valve cover, and rear access with the bed raised fully. Use those access points when setting stance instead of compensating with bed-servo travel.[1] 1993 Nissan Hardbody Bed Dancer Founders Edition factory setup and maintenance manual (opens in a new tab)
OEM parts
Drivetrain
5Complete differential (1pc)
Axle input shaft and gear set
Left/right rear axle shafts (1pr)
Chrome center driveshaft (1pc)
Suspension
7Front/rear plastic shock assemblies (1pr)
Spec sources
Black rear suspension links (1set)
Cable rod ends (2pcs)
Z rack rod ends (2pcs)
Chrome Z rack hinge (1pc)
Chrome lower control arms (1pr)
Chrome upper control arms (2pcs)
Steering
98kg micro servo with aluminum case and 190mm lead (1pc)
8kg micro servo with aluminum case and 410mm lead (1pc)
Hexfly HX-50BL servo
226mm servo extension (1pc)
205mm servo extension (1pc)
Aluminum servo horn set
Chrome Z rack servo mount (1pc)
Steering link (1pc)
Electronics
2RC380 brushed motor (1pc)
R6A 2-in-1 ESC and receiver (1pc); BEC ratings conflict
Wheels & tires
5Premounted Radial 15 tires with five-hole mag wheels (1set)
Radial 15 tires with foam (4pcs)
Premounted R15 Radial tires with 40-spoke chrome wheels (1set)
R15 Radial tires with foam (4pcs)
Five-hole chrome mag wheels (1set)
Chassis & body
31993 Nissan D21 hardbody kit, grey (1set)
1993 Nissan D21 hardbody cab, grey (1pc)
1993 Nissan D21 hardbody hood with side panels, grey (1set)
Unclassified
18Complete transmission (1pc)
Black steel frame rail set
Black battery tray (1pc)
236mm battery straps (2pcs)
Chrome cable retention brackets (1set)
Chrome Z rack pushrods (2pcs)
Z rack cable set
Chrome Z rack plates (1set)
49 collected part numbers. Collected . Unmarked parts are recorded listings, without a claim about factory installation; optional and upgrade listings are tagged. Key assemblies include recorded gear and shock identifiers. Open a part for its listing sources.
About these specs
Current factory support labels this manual BED DANCER - FOUNDERS EDITION.
Read moreShow less
- MAN-Bed Dancer-26-5-14 identifies RER13454 RC380 motor, RER14764 complete transmission, RER15741 R6A 2-in-1 ESC/receiver and LR6X radio.
- Exact retailer RER43259 is the orange Founders Edition.
- Manual p.26 table says 8.2V/8A BEC, its pictured label says 8.2V/10A, prose says 5A/7.4V and p.85 part caption says 10A/up to8.4V.
- These do not establish one factory output setting.
- No gearing, tire outside diameter or motor shaft is borrowed from another lowrider.
- The wheel-hex size is a working estimate from the exact RER13441 replacement; wheel offset and mounting hardware remain specific to this edition.
Sources
6 source links for this model.
Read moreShow less
- Manuals, exploded views, and parts lists.
- Vehicle product and specification pages.
- Individual part and electronics specifications.
Links open in a new tab.
Maker documents
1- Founders Edition Bed Dancer factory manual (opens in a new tab)Supports 8 specificationsMAN-Bed Dancer-26-5-14; English control guide pp. 5-30; exploded view Physical PDF pp. 82-83; parts list Physical PDF pp. 84-88Used forMain specsMotor shaftSizeBattery fitElectronicsSuspensionPowerSteering & radioBackground
This vehicle
2- Redcat Racing 1993 Nissan Hardbody Bed Dancer Founders Edition product page (opens in a new tab)Supports 2 specificationsUsed forMain specsSizeBackground
- Redcat Racing 1993 Nissan Hardbody Bed Dancer Founders Edition product page (opens in a new tab)Supports 2 specificationsUsed forMain specsSize
Parts and electronics
3- Redcat racing 1 10 founders edition bed dancing mini truck rtr (opens in a new tab)Supports 1 specificationUsed forMain specs
- RER13441 1 (opens in a new tab)Supports 2 specificationsUsed forWheel hexWheels & tires
- Redcat hex wheel hub axle pin set (opens in a new tab)Supports 2 specificationsRetailer listingUsed forWheel hexWheels & tires
