VehiclesTraction Hobby Porsche 934

- Scale
- 1/6
- Drive
- 4WD
- Max LiPo
- 6S
- Power
- brushless
Background
The Porsche 934 is a 1/6-scale rally car in Traction Hobby's range.1 Its equipment includes licensed Porsche body; independent suspension at all four wheels; front, center and rear differentials; selectable rear or four-wheel drive; a separate brake servo.1 The body and suspension package give this version its own place within the range.1 Check the edition before choosing service parts, since the model family also includes different suspension layouts, body packages and electronics.1
Specifications
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Rally | |
| Drive | 4WD | |
| Power | Brushless | |
| Build | Ready to run | |
| Scale | 1/6 | |
| Drivetrain | ||
| ||
| Pinion | 15TStock | Stock |
| Spur | Not published | |
| Transmission & axle | Not published | |
| Final drive | Not published | |
| Wheels & tires | ||
| ||
| Tire diameter | 104mmStock | Stock |
| Power | ||
| ||
| Motor | Not published | |
| Battery | Up to 6SLiPoStock | Stock |
| Performance | ||
| ||
| Theoretical top speed | Not published | |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Not published means it exists but no source we could find prints it.
Build and setup
Factory setup guide for this configuration.
Set up the Porsche 934 around its selectable 2WD/4WD drivetrain before changing the motor. Bring the car to a stop for each drive-mode change and check that the shift servo reaches both positions without binding. If a shift does not complete, inspect that linkage and its travel rather than holding the servo against a mechanical stop.[1] Porsche 934 factory setup manual (opens in a new tab)
Investigate heat with the complete drivetrain in mind. The factory troubleshooting guide pairs cooling checks with lower gearing and an inspection for seized or obstructed transmission parts. Start with free-running bearings, correct pinion mesh and clear cooling airflow, then compare the same run. A larger battery or taller pinion should not be used to compensate for binding.[1] Porsche 934 factory setup manual (opens in a new tab)
Read moreRead less about build and setup for Porsche 934
Keep wheel-hex pins, center-shaft fasteners and steering travel in the service routine. The manual distinguishes a motor that spins without driving the wheels from a servo that buzzes at its travel limit. Inspect the corresponding mechanical connection before replacing electronics, and reconnect the shell's lighting lead when refitting the body.[1] Porsche 934 factory setup manual (opens in a new tab)
OEM parts
Drivetrain
More document pages (14)
Center Diff Axle Shaft
Pinion Gear 15 Tooth
Spec sources
Spur Gear 48 Tooth
43T Spiral Bevel Gear
Spiral Pinion Gear 10 Tooth
Hard Steel Differential Gear Set
Differential Gear Shaft
Suspension
More document pages (13)
4x55mm Turnbuckle
5x42mm Turnbuckle
5x50mm Turnbuckle
4x71.4mm Arm Shaft
4x68.6mm Arm Shaft
3x43mm Arm Shaft
3x44.5mm Arm Shaft
Shock Stand Off
Steering Block
Servo Saver Set
Steering Ball Buckle
Servo Arm
Steering Rack Bushin
Steering Post
Receiver Box Servo Mount
Steering Servo Tie Rods
Electronics
More document pages (1)
ESC Mount Plate
Quick-Release Motor Mount 4985
Wheels & tires
More document pages (1)
3.0” Simulated Wheels
Tire Cover
Front and Rear Wheel Couplings
Chassis & body
More document pages (12)
Chassis Brace
Front Bumper Set
Main Chassis
Front Swingarm Mount-FF
Front Swingarm Mount-FR
Rear Swingarm Mount-RF
Rear Swingarm Mount-RR
Bumper Light
Hardware & seals
More document pages (22)
M4x10 Droop Screw
M5x8 Pan Head Screw
M5 Locking Washer
M2.5 Nylon Nut
M3 Nylon Nut
M3 Nut
M4 Nylon Nut
M3 Flanged Nylon Nut
Unclassified
More document pages (35)
Front Hub Carriers 10 Degree
Rear Hub Carriers
Battery case
Mount
6.8mm Ball End-Upper
5.8mm Swaybar Ball End
Antenna Sleeve
Battery Strap 25x300mm
176 collected part numbers. Collected . Unmarked parts are recorded listings, without a claim about factory installation; optional and upgrade listings are tagged. Key assemblies include recorded gear and shock identifiers. Open a part for its listing sources.
About these specs
Maker table allows 3S to 6S; co-branded Primal red manual specifies only 4S or 6S.
Read moreShow less
- Maximum 6S agrees; no 3S operating recommendation is transferred to the Primal configuration.
- Red and Gulf paint choices are grouped, with Gulf hood lights noted separately.
Sources
3 source links for this model.
Read moreShow less
- Manuals.
- Individual part and electronics specifications.
Links open in a new tab.
Maker documents
1- Porsche 934 instruction manual (Primal RC / Traction Hobby PDF) (opens in a new tab)Supports 2 specificationsUsed forMain specsGearing
Parts and electronics
2- Porsche 934 manufacturer product and specification graphic (opens in a new tab)Supports 1 specification · Background 1Traction HobbyUsed forMain specsBackground 1
- Manuals (opens in a new tab)Supports 1 specificationUsed forMain specs