VehiclesSerpent SRX8-E Pro 1/8 4wd

- Scale
- 1/8
- Drive
- 4WD
- Max LiPo
- 4S
- Power
- electric
Background
The SRX8-E Pro is Serpent's 1/8 four-wheel-drive electric race-buggy kit. A 4mm 7075-T6 aluminum chassis supports a reversible motor mount and a block battery layout; the mount can also be repositioned for a saddle arrangement. The suspension uses 16mm threaded shocks with 3.5mm shafts and a cap that supports bladder or emulsion builds. Serpent (opens in a new tab).
Read moreShow less
The standard battery layout accommodates either one 4S pack or two 2S packs combined as a 4S battery. Motor, ESC and gearing choices remain part of the build, and the manual explicitly leaves the motor pinion out of the kit. Select those components together rather than treating the chassis as a fixed ready-to-run power package. Serpent manual (opens in a new tab).
Specifications
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Buggy | |
| Drive | 4WD | |
| Power | Motor not included | |
| Build | Kit | |
| Scale | 1/8 | |
| Part number | SER600021 | |
| Drivetrain | ||
| ||
| Pinion | Not published | |
| Spur | Not published | |
| Transmission & axle | 3.38:1DerivedSources(9)
| Derived |
| Final drive | Not published | |
| Wheels & tires | ||
| ||
| Tire diameter | Not published | |
| Wheel hex | 17 mmSingle report | Single report |
| Suspension | ||
| ||
| Chassis | 7075-T6 aluminum4 mm thickStock | Stock |
| Shocks | Threaded3.5 mm shaft, front and rearStock | Stock |
| Front shock lengths | 108 mm factory default full-droop settingFactory setup setting; do not treat as maximum extended replacement-shock length.Stock | Stock |
| Rear shock lengths | 127 mm factory default full-droop settingFactory setup setting; do not treat as maximum extended replacement-shock length.Stock | Stock |
| Power | ||
| ||
| Motor | Not published | |
| Battery | Up to 4SLiPoStockSources(9)
| Stock |
| Battery pack configuration | 1 × 4S or 2 × 2STwo 2S packs combined as a 4S batteryStock | Stock |
| Motor mount material | 7075-T6 aluminumStock | Stock |
| Performance | ||
| ||
| Theoretical top speed | Not published | |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Derived uses recorded dimensions or arithmetic. The row explains the inference. A nominal mating size is not a measured tolerance or a complete fitment guarantee.
- Single report uses one outside source. It is useful as a starting figure, with the source and calculation described in the note.
- Not published means it exists but no source we could find prints it.
Build and setup
Factory setup guide for this configuration.
Use the SRX8-E Pro 1/8 4wd differential assembly drawings to keep the seal, shims and oil-fill procedure consistent during a rebuild. The manual gives a fill reference above the crosspin and sends viscosity selection to the matching setup sheet. Check the mechanical assembly before changing oil to alter the car’s behavior.[1] SRX8-E Pro 1/8 4wd factory setup manual (opens in a new tab)
For the illustrated shock caps, release trapped air with the shaft extended, then complete the bleed with the rod fully inward before fitting the sealing O-ring and screw. Keep the front and rear shaft arrangements matched to their drawings and record the spring and oil combination when comparing track setups.[1] SRX8-E Pro 1/8 4wd factory setup manual (opens in a new tab)
OEM parts
Drivetrain
42Ballbearing 8x16x5 NSK (2)
Ball-bearing 5x8x2.5 (2)
Ballbearing 5x8x2.5 flanged
Ballbearing 6x10x3 (2)
Ballbearing 13X19X4 SS (2)
Driveshaft 98mm (2)
Driveshaft insert (2)
Suspension
58Hingepin (2)
Hingepin RR outer (2)
Shock-pivot bushing delrin (4)
Suspension bracket RR FR SRX8
Suspension bracket RR RR SRX8
Suspension bracket FR FR SRX8
Suspension bracket FR RR SRX8
Shock mount alu hardcoated (2) SRX8
Steering
26Steeringrack mount
Servosaver shaft outer
Pivot ball steering rod (2)
Servo saver post alu (2)
Servo saver spring hard
Servo spacers (8)
Servosaver post (2) SRX8
Pivot ball steering (4) SRX8
Electronics
2Motormount set SRX8E
Motor slider SRX8E
Wheels & tires
10Wheelnut 17mm (4)
Spacers 1,25mm + 2,5mm for wheelbase (4+2)
Tire mounting band 1/8 buggy orange (4)
Wheel axle (2) SRX8
Wheel axle sleeve (2) SRX8
Wheelhexagon 0mm (2) SRX8
Wheelhexagon +1mm (2) SRX8
Wheelhexagon 0mm light (2) SRX8
Chassis & body
18Body clips (10)
Wing black nylon
Wing white low 811
Wing black low 811
Bumper SRX8
Wing mount plates (2+2) SRX8
Wing mount post alu SRX8
Wing straight MD black 1/8
Hardware & seals
57screw allen countersunk m3x10 (10)
screw allen countersunk m4x8 (10)
Screw allen countersunk m4x10 (10)
screw allen countersunk m4x16 (10)
screw allen countersunk m4x12 (10)
Screw allen cilinderhead m3x16 (10)
screw allen roundhead m3x6 (10)
screw allen roundhead m3x10 (10)
Unclassified
66Grommet rubber soft (4)
setscrew allen m3x4 (10)
setscrew allen m3x3 (10)
setscrew allen m4x4 (10)
setscrew allen m4x6 (10)
Setscrew allen M3x6 (10)
Setscrew allen M5x4 (10)
Pin 2.5x13 (10)
279 collected part numbers. Collected . Unmarked parts are recorded listings, without a claim about factory installation; optional and upgrade listings are tagged. Key assemblies include recorded gear and shock identifiers. Open a part for its listing sources.
About these specs
The 17 mm mating wheel hex is a single-source retailer specification, with exact OEM component mapping where derived; hex offset and wheel-nut size are separate.
Sources
10 source links for this model.
Read moreShow less
- Manuals, parts lists, and setup sheets.
- Vehicle product and specification pages.
- Individual part and electronics specifications.
Links open in a new tab.
Maker documents
3- SRX8 EPRO ManualV1.1 (opens in a new tab)Background referenceUsed forBackground
- SRX8-E Pro 1/8 4wd reference parts guide (opens in a new tab)Supports 3 specificationsUsed forMain specsWheel hexWheels & tires
- SRX8-E Pro 1/8 4wd factory default setup (opens in a new tab)Supports 2 specificationsUsed forMain specsSuspension
This vehicle
2- Serpent SRX8-E Pro 1/8 4wd product page (opens in a new tab)Supports 3 specificationsUsed forMain specsSuspensionPowerBackground
- Serpent SRX8-E Pro 1/8 4wd product page (opens in a new tab)Supports 1 specificationUsed forMain specs
Parts and electronics
5- Race off road (opens in a new tab)Supports 1 specificationUsed forMain specs
- RC car (opens in a new tab)Supports 1 specificationUsed forMain specs
- SRX8EPROMANUALV11 (PDF) (opens in a new tab)Supports 1 specificationUsed forMain specs
- 600072 serpent serpent SRX8 GT R 1 8 4WD GP EN (opens in a new tab)Supports 3 specificationsRetailer listingUsed forMain specsWheel hexWheels & tires
- Ref guide SRX8GT R V1.3 (600072).XLS (opens in a new tab)Supports 3 specificationsUsed forMain specsWheel hexWheels & tires
