VehiclesSerpent SRX8 PRO GP 1/8 4wd

- Scale
- 1/8
- Drive
- 4WD
- Max LiPo
- -
- Power
- nitro
Background
The SRX8 PRO GP is a 1/8 four-wheel-drive nitro buggy kit developed from the SRX8 and SRX8 Evo. It returns to a captured center driveline with greased, booted joints and introduces larger-volume differentials with Mod 1.25 internal gears. Serpent (opens in a new tab).
Read moreShow less
The Pro also changes the steering system and raises the wing mount by 15mm. Optional chassis weights provide a way to adjust weight distribution, while the kit format leaves the engine and radio installation to the builder. Check the exact Pro manual and option list when ordering components. Serpent (opens in a new tab).
Specifications
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Buggy | |
| Drive | 4WD | |
| Power | Nitro | |
| Build | Kit | |
| Scale | 1/8 | |
| Part number | SER600020 | |
| Drivetrain | ||
| ||
| Pinion | Not published | |
| Spur | Not published | |
| Transmission & axle | Not published | |
| Final drive | Not published | |
| Wheels & tires | ||
| ||
| Tire diameter | Not published | |
| Power | ||
| ||
| Motor | Not published | |
| Battery | Not published | |
| Performance | ||
| ||
| Theoretical top speed | Not published | |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Not published means it exists but no source we could find prints it.
Build and setup
Factory setup guide for this configuration.
Use the SRX8 PRO GP 1/8 4wd differential assembly drawings to keep the seal, shims and oil-fill procedure consistent during a rebuild. The manual gives a fill reference above the crosspin and sends viscosity selection to the matching setup sheet. Check the mechanical assembly before changing oil to alter the car’s behavior.[1] SRX8 PRO GP 1/8 4wd factory setup manual (opens in a new tab)
For the illustrated shock caps, release trapped air with the shaft extended, then complete the bleed with the rod fully inward before fitting the sealing O-ring and screw. Keep the front and rear shaft arrangements matched to their drawings and record the spring and oil combination when comparing track setups.[1] SRX8 PRO GP 1/8 4wd factory setup manual (opens in a new tab)
OEM parts
Drivetrain
39Ballbearing 5x13x4 NSK (2)
Ballbearing 8x16x5 NSK (2)
Ball-bearing 5x8x2.5 (2)
Ballbearing 5x8x2.5 flanged
Ballbearing 6x10x3 (2)
Ballbearing 13X19X4 SS (2)
Driveshaft 98mm (2)
Suspension
54Hingepin (2)
Hingepin RR outer (2)
Shock-pivot bushing delrin (4)
Suspension bracket RR FR SRX8
Suspension bracket RR RR SRX8
Suspension bracket FR FR SRX8
Suspension bracket FR RR SRX8
Shock mount alu hardcoated (2) SRX8
Steering
30Steeringrack mount
Servosaver shaft outer
Pivot ball steering rod (2)
Servo saver post alu (2)
Servo lever steering 23T alu
Servo lever steering 24T alu
Servo lever steering 25T alu
Servo saver spring hard
Wheels & tires
13Flywheel alu 34mm
Wheelnut 17mm (4)
Flywheel steel 34mm
Spacers 1,25mm + 2,5mm for wheelbase (4+2)
Flywheel 3-pin alu
Tire mounting band 1/8 buggy orange (4)
Wheel axle (2) SRX8
Wheel axle sleeve (2) SRX8
Chassis & body
23Body clips (10)
Wing black nylon
Wing white low 811
Wing black low 811
Body SRX8 clear
Body SRX8 High Downforce
Chassis alu hard coated SRX8
Body mount set FR + RR SRX8
Hardware & seals
62screw allen countersunk m3x10 (10)
screw allen countersunk m4x8 (10)
Screw allen countersunk m4x10 (10)
Screw allen countersunk M3x8 (10)
screw allen countersunk m4x12 (10)
Screw allen cilinderhead m3x16 (10)
screw allen roundhead m3x6 (10)
screw allen roundhead m3x10 (10)
Unclassified
126Grommet rubber soft (4)
setscrew allen m3x4 (10)
setscrew allen m3x3 (10)
setscrew allen m4x6 (10)
setscrew allen m5x6 (10)
Setscrew allen M3x6 (10)
Setscrew allen M5x4 (10)
Pin 2.5x13 (10)
347 collected part numbers. Collected . Unmarked parts are recorded listings, without a claim about factory installation; optional and upgrade listings are tagged. Key assemblies include recorded gear and shock identifiers. Open a part for its listing sources.
Sources
4 source links for this model.
Read moreShow less
- Manuals.
- Vehicle product and specification pages.
- Individual part and electronics specifications.
Links open in a new tab.
Maker documents
1- 828 PRO ManualV1.1 (opens in a new tab)Supporting reference
This vehicle
1- Serpent SRX8 PRO GP 1/8 4wd product page (opens in a new tab)Supports 1 specificationUsed forMain specsBackground
Parts and electronics
2- Race off road (opens in a new tab)Supports 1 specificationUsed forMain specs
- RC car (opens in a new tab)Supports 1 specificationUsed forMain specs
