VehiclesRlaarlo XTS-F10 Carbon Fiber Roller
Rlaarlo XTS-F10 Carbon Fiber Roller
1/10 scale · rally · XTS-F10-Roller
Rlaarlo's XTS-F10 Carbon Fiber Roller is the four-wheel-drive 1/10 rally car without motor, ESC, servo, radio or battery, so the builder chooses the power system.
The 65T spur drives a 3.09:1 differential stage, so the final drive is 65 divided by the pinion, times 3.09. The car rolls on 75 mm tires. Choose the motor and pinion together in the gearing calculator, since the pair decides both the top speed and how hot the motor runs.
- Tire
- 75mm
Sold without a motor, so there is no stock KV: compare gearing by rollout.

Specifications
Last modified
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Rally | |
| Drive | 4WD | |
| Power | Motor not included | |
| Build | Roller / ARR | |
| Scale | 1/10 | |
| Part number | XTS-F10-Roller | |
| Drivetrain | ||
| ||
| Pinion | Not published | |
| Spur | 65TStock | Stock |
| Transmission & axle | 3.09:1Derived | Derived |
| Final drive | Not published | |
| Wheels & tires | ||
| ||
| Tire diameter | 75mmStock | Stock |
| Power | ||
| ||
| Motor | Not applicable | |
| Battery | Not applicable | |
| Performance | ||
| ||
| Theoretical top speed | Not applicable | |
| Size & weight | ||
| ||
| Length | 445 mm17.5 inStock | Stock |
| Width | 218 mm8.6 inStock | Stock |
| Height | 178 mm7 inStock | Stock |
| Wheelbase | 257 mm10.1 inStock | Stock |
How to read these figures
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Derived is worked out from gear tooth counts the maker publishes rather than printed as a ratio; the notes below say how.
- Not applicable means the vehicle does not come with it, like the motor on a roller or the tires on a race kit, or does not have one, like a KV rating on a brushed motor.
- Not published means it exists but no source we could find prints it.
How these numbers were settled
Roller: motor, ESC, servo, radio and battery are not included, so the KV and cell count are the buyer's.
- Rlaarlo's manual (p. 18) lists the roller's pinion as 24-27T in both English and Chinese with no fitted count, and the box list names one free motor gear, so the pinion and final drive are left blank.
- The spur is 65T (0.53M/48P) and the differential stage pairs an 11T pinion with a 34T ring gear, which is 3.09:1 after the spur, worked out from the printed tooth counts.
- The tire is 75mm in diameter and 30mm wide.
- The drive is four-wheel drive with three differentials.
Sources
Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.
Maker documents
1- XTS-F10 user manual (Rlaarlo PDF) (opens in a new tab)Supports 2 specificationsConfiguration table p. 18Used forMain specsSize
This vehicle
1- Rlaarlo XTS-F10 Carbon Fiber Roller product page (opens in a new tab)Supports 2 specificationsUsed forMain specsSize
Parts and electronics
2- Xtsversion detail parameter.png (opens in a new tab)Supports 1 specificationUsed forMain specs
- 65T spur gear cnc for RC parts (opens in a new tab)Supports 1 specificationUsed forMain specs
