VehiclesKyosho Fazer D2 FZD2

Kyosho

Kyosho Fazer D2 FZD2 Chassis

1/10 scale · 2WD drift chassis · sold as kits

Kyosho's Fazer D2 FZD2 is a 1/10 rear-wheel-drive drift chassis with a 260 mm standard wheelbase, sold as readysets under several scale bodies.

Every readyset shares the 84T spur and a 2.60:1 stage after it, with a spool rather than a differential on the rear axle. The wheelbase adjusts at the chassis joints, which lets one chassis fit many drift bodies. The pinion, motor and tires come with each kit rather than with the chassis, so enter yours in the gearing tool.

Transmission & axle
2.60:1
Spur
84T
Wheelbase
260mm
Introduced
2025

The pinion, motor and tires come with each kit: enter yours in the gearing tool.

Kyosho Fazer D2 FZD2
Photo: Kyosho (opens in a new tab)

Kits on this chassis Built on the Fazer D2 FZD2

Each kit adds its own body, tires, pinion and motor. The chassis figures below apply to all of them.

KitPart no.Maker page
Toyota Sprinter Trueno AE86 White34501T1rc.kyosho.comPage (opens in a new tab)
Toyota 86 GT Tuned Ver. Lightning Red34502T1rc.kyosho.comPage (opens in a new tab)
2021 Toyota Tundra Drift Ver. Black (FZD2L)34531T1rc.kyosho.comPage (opens in a new tab)
Nissan Silvia S13 Tuned Ver. Purple34503T1rc.kyosho.comPage (opens in a new tab)

Specifications

Last modified

SpecValueBasis
Vehicle
ClassDrift
Drive2WD
Scale1/10
Drivetrain
PinionWith each kit
Spur84TStockStock
Transmission & axle2.60:1DerivedDerived
Final drive5.90 to 13.65:1 on 37T to 16T pinionsMaker's chartMaker's chart
Wheels & tires
Tire diameterWith each kit
Power
MotorWith each kit
BatteryWith each kit
Size & weight
Wheelbase260 mm10.2 inStockStock
How to read these figures
  • Stock is as the vehicle ships.
  • Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
  • Derived is worked out from gear tooth counts the maker publishes rather than printed as a ratio; the notes below say how.
  • With each kit means each kit on this chassis brings its own, so enter yours in the gearing tool.
  • Maker’s chart is the ratios the maker prints for this chassis with the pinions it names.

Other versions of this chassis

Gearing parts

Pinion and spur parts for the Kyosho Fazer D2 FZD2: fitted, and optional gearing supplied in the box
ComponentTeethPitchBorePart number
Fitted at the factory
Spur84T48PNot applicableFA601 (opens in a new tab)
About teeth, pitch and bore
  • Tooth counts are the ones in the specifications above.
  • Pitch is given as metric module (Mod 1, Mod 0.8) or diametral pitch (32P, 48P). They are different standards and are not interchangeable, even where the numbers look close.
  • Bore is the pinion’s hole, listed separately from the motor shaft.
  • Linked part numbers go to the maker’s or official distributor’s page for that part.

How these numbers were settled

Every FAZER D2 readyset prints 'Gear Ratio 9.1:1'.

Sources

Every figure on this page traces to one of these; where they disagreed, the note above says which was used and why. Links open in a new tab.

Parts and electronics

More from Kyosho

All Kyosho vehicles