VehiclesTamiya TB-03

- Scale
- 1/10
- Drive
- 4WD
- Max LiPo
- -
- Power
- -
Background
TB-03 is a longitudinal-motor, shaft-driven four-wheel-drive touring chassis with inboard front suspension. The molded bathtub frame includes a motor-cooling duct, while the drivetrain uses a three-piece propeller-shaft arrangement and ball differentials at both axles. Factory reference (opens in a new tab). Assembly manual (opens in a new tab).
Read moreShow less
The factory description identifies short reversible suspension arms and front and rear uprights derived from the TRF416. CVA super-mini oil dampers support the double-wishbone suspension. These details describe a specific touring architecture rather than a promise that every TRF or TB-series part can be transferred as a complete assembly. Factory reference (opens in a new tab). Assembly manual (opens in a new tab).
One body kit is the ORC Amemiya SGC-7, number 58425, representing the rotary-powered Mazda-based car from the 2008 Super GT season. Its body dimensions,64 mm tires and 7.09:1 final drive belong to that complete kit. Keep the body package and installed gearing with a running setup, and identify the standard TB-03 before applying drift or TB-03R equipment. Factory reference (opens in a new tab). Assembly manual (opens in a new tab).
Kits on this chassis Built on the TB-03
Each kit adds its own body, tires, pinion and motor. The chassis figures below apply to all of them.
Read moreShow less
| Kit | Part no. | Maker page |
|---|---|---|
| 58425 | tamiya.comPage (opens in a new tab) |
Specifications
| Spec | Value | Basis |
|---|---|---|
| Vehicle | ||
| ||
| Class | Touring | |
| Drive | 4WD | |
| Build | Kit | |
| Scale | 1/10 | |
| Drivetrain | ||
| ||
| Pinion | With each kit | |
| Spur | Not published | |
| Transmission & axle | Not published | |
| Final drive | With each kit | |
| Wheels & tires | ||
| ||
| Tire diameter | With each kit | |
| Power | ||
| ||
| Motor | With each kit | |
| Battery | With each kit | |
How to read these figures
- Chassis figures are shared references. Motors, electronics and supplied extras depend on the exact numbered kit.
- Stock is as the vehicle ships.
- Calculated is worked from the stock figures on this page rather than stored beside them, so the two cannot drift apart.
- Not published means it exists but no source we could find prints it.
- With each kit means each kit on this chassis brings its own, so enter yours in the gearing tool.
Build and setup
Factory setup guide for this configuration.
Use the shared TB-03 chassis manual for the inboard front suspension and shaft-driven transmission, then use the exact 58425 body instructions for the ORC Amemiya build. Check that the rockers and linkage move freely before adjusting the front damping.[1] Exact factory product and historical description (opens in a new tab)[2] Exact factory assembly and setup manual (opens in a new tab)
Inspect the ball differentials, three-piece propeller shaft and bearing supports before adding motor power. The 58425 product page lists 64 mm tires and a 7.09:1 ratio, but those figures are not a universal setup for every TB-03 body kit.[1] Exact factory product and historical description (opens in a new tab)[2] Exact factory assembly and setup manual (opens in a new tab)
OEM parts
Drivetrain
10TB Evolution V Ball Differential Gear Set
TB-03 0.6 Module Spur Gear (64T)
1510 Ball Bearing
1060 Ball Bearing
1050 Ball Bearing
850 Ball Bearing
TA04 Ball Differential Plate Set
Suspension
5TB-03 D Parts (Suspension Arm)
CVA Mini Shock Unit II V Parts
TB Evolution IV 46mm Suspension Shaft
TB Evolution IV 2.6mm Suspension Shaft Set
CVA Mini Shock Unit II Oil Seal
Steering
1DF-02 Q Parts (Servo Saver)
Electronics
1540-J Motor
Chassis & body
1TB Evolution V B Parts (Bumper)
Hardware & seals
13x5mm Flat Screw
Unclassified
7TB-03 C Parts (Front Upright)
TB-03 E Parts (Rear Upright)
TA05-IFS F Parts (Hub Carrier 4 Degrees)
TB-03 M Parts (Damper Stay)
TRF Damper Urethane Bushing
TB Evolution IV Flanged Tube
4mm Adjuster
26 collected part numbers. Collected . Unmarked parts are recorded listings, without a claim about factory installation; optional and upgrade listings are tagged. Key assemblies include recorded gear and shock identifiers. Open a part for its listing sources.
About these specs
Exact numbered assembly kit.
Read moreShow less
- Radio and ESC are separate purchases; the kit has no universal maximum LiPo cell rating.
- Unknown tooth counts or dimensions are not borrowed from another edition.
Sources
3 source links for this model.
Read moreShow less
- Manuals and parts lists.
- Individual part and electronics specifications.
Links open in a new tab.
Maker documents
1- TB-03 assembly manual (Tamiya PDF) (opens in a new tab)Supports 1 specificationparts list Exact 58425 edition; service-card references only.Used forMain specsBackground
Parts and electronics
2- Factory reference (opens in a new tab)Supports 1 specificationUsed forMain specsBackground
- Products 58409 (opens in a new tab)Supports 1 specificationUsed forMain specs
